You are here: Home > Dell > Dell Printer Support FAQ's

Dell C3000 series Error code 004-332 restart printer

One of the toner cartridges was not in the locked position - lock it down and the printer works.

For the full thread, click here for the Dell community support forum


Dell c3000/3100cn and 016-310 "Restart Printer" message

Turn off the printer, and then hold down the "Menu" button on the front of the printer, and then turn on the power to the printer.

You should see the "Init Password" message on the front panel, and just choose No to not init the password. It should be resolved.

For the full thread, click here for the Dell community support forum 

Dell Color Laser Printer 3000cn/3010cn/3100cn 009-340 Error Message

  1. Reseat the imaging drum cartridge.

  2. Turn the printer off using the power switch on the left side.

  3. Wait 10 seconds, turn the printer back on, and check if the error message still occurs.

  4. If the error message persists, run diagnostics on the Automatic Density Control (ADC) sensor solenoid nip.
    1. Turn the printer off using the power switch on the left side of the printer.
    2. Press and hold the up and down buttons while turning the printer on. Release the buttons when Customer Mode appears on the printer LCD.
    3. Press the down arrow until IOT DIAG appears, and then press Select (  ).
    4. Press the down arrow until Digital Output appears, and then press Select (  ).
    5. Press the up arrow until D0-1c appears, and then press Select (  ). A click noise should be heard.
    6. Press Cancel to stop the test. If the click noise is not heard, Dell Contact Technical Support.
    7. If the click noise is heard, run diagnostics on the ADC sensor solenoid release by pressing the down arrow until  D0-1dappears, and then press Select (  ). A click noise should be heard.
    8. If the click noise is not heard, Dell Contact Technical Support.

  5. If the click noise is heard, Dell Contact Technical Support.






Error Message:"Low or No Ink"

This happens because there is no way to reset the chip that reads the ink levels, so the cartridge is reading the old ink level and not the new, refilled one. Especially with Dells and Lexmarks, this is quite common; but directions are enclosed with each cartridge on how to bypass this error message so you can still print. Below is a picture of what usually pops up. Just tick the "Don't display this dialog box again" to continue printing.
 
 
Error with Dell J5566/ M4640/ J5567/ M4646/ J4844 inkjet cartridges?
 
Even though you have a different Dell printer model with Dell 922 Photo All-In-One, if the almost same symptom appears as below, please follow the method below. The instructions below are geared to the Dell All-in-One Printer; however the majority of Dell printers will have a similar method for disabling the error message.

Option 1: When the window of 'Reserve Tank' appears click the 'Don't display this dialog again' check box, and then click the 'Continue Printing' button.

Option 2: When the window of 'Printing Status' appears

If the Dell printer solution center is installed on your computer:

Step 1
Click the Windows Start button and then click "All Programs".

Step 2
Click the "Dell Printer" -> "Dell Photo AIO Printer 922" -> "Dell printer solution".

Step 3
Click the "Advanced" button.

Step 4
Click the "Printing status" button.

Step 5
Check the "Never display the Printing Status" radio button, and then click "OK".


If the Dell printer solution center is not installed on your computer:

Step 1
Click the Windows Start button and then click "Control Panel".

Step 2
Double-click the Printer and Faxes folder.

Step 3
Right-click the icon for your printer and choose Preferences.

Step 4
Click the "Options" menu, in the upper right-hand corner of the window.

Step 5
Click the "Printing Status Options".

Step 6
Check the "Never display the Printing Status" radio button, and then click "OK".